Tempoverrides что за команда
10 AutoCAD temporary override keys
We all have preferences when we work. Also when we work with AutoCAD. We set some settings to let us work comfortably. However, sometimes we need to change the settings temporarily. Sometimes just for creating one particular object.
AutoCAD has some useful override keys to temporarily use some features. So you don’t need to click any button to turn it on then click it again to turn it off.
For example, turning on object snaps can be annoying if you work on complex drawing. You can just set it off. When you need to use it, just use the temporary override keys.
About temporary override keys
These temporary override keys only work when AutoCAD ask you to input coordinate. It means you need to have an active command before you can use it.
You might need to hold the override key for 1-2 seconds before you can use it. You can confirm when the override key is active when you see the down arrow near your crosshair.
Some override keys will activate a feature if you have it turned off, and will deactivate that feature if you have it turned on.
If you use two key combination, make sure you release the character key first and shift key last. Otherwise, You will have the character filled in command line and won’t allow you to click any point.
Let’s see the 10 override keys that you can use in AutoCAD.
1. Toggles orthogonal mode
Override key: Hold SHIFT
This is probably the most known override key. This key is useful when you need to create a horizontal or vertical line. After you click the first point, hold SHIFT key.
2. Toggles OSNAP mode
Override key: Hold SHIFT A (right handed) or SHIFT+ ‘ (left handed)
This key will change OSNAP mode temporarily. If you use it when OSNAP is on, then this will turn it off. If OSNAP is off, this will turn it on.
3. Toggles Polar mode
Activating polar mode will make your crosshair sticky when it’s near to defined angle.
You can turn it on/off temporarily by pressing this key.
4. Enables Snap Enforcement
Override key: Hold SHIFT + S or SHIFT + ;
This key will activate snap enforcement, changing OSNAPOVERRIDE system variable from 0 to 1.
Snap enforcement will only allow you to click a point if it’s defined in OSNAP. For example, if you use this with settings below, you can only snap to endpoint, center, and extension. You can’t snap to midpoint, quadrant or any other point. You also can’t click on empty space.
5. Toggles Object Snap Tracking mode
Override key: SHIFT + Q or SHIFT + ]
This key will change Object Snap Tracking Mode. This is similar to pressing F11.
6. Toggles Snap Override: Endpoint
Override key: SHIFT + E or SHIFT + P
I personally prefer to use SHIFT + right click to get full snap override menu. However, using this key is nice if you only often use endpoint, midpoint and center snap.
This is similar to enabling endpoint snap from toolbar or context menu.
7. Toggles Snap Override: Midpoint
Override key: SHIFT + V or SHIFT + M
8. Toggles Snap Override: Center
9. Disable All Snapping and Tracking
Override key: SHIFT + D or SHIFT + L
This key will turn off these keys at once.
10. Toggles Dynamic UCS mode
Override key: SHIFT + Z or SHIFT + /
This will disable dynamic UCS. If you are not familiar with dynamic UCS, read this 7 AutoCAD tips and trick using dynamic UCS.
You can assign your own override keys!
Let’s open CUI editor. Expand keyboard shortcuts> temporary override keys. You can see several predefined override is not defined yet. You can change and assign your preferred keys there.
Are you already using these keys? Which one is your favorite? Share with us here!
About Edwin Prakoso
I work as a Sr. Technical Consultant in Tech Data Advanced Solutions Indonesia. I’ve been using AutoCAD since R14 and Revit since Revit Building 9. I occasionally write for AUGIWorld magazine and also active in Autodesk discussion forum.
I’m an Autodesk Certified Professional (ACP) for Revit Architecture and AutoCAD. I’m also a member of Autodesk Expert Elite, appreciation for individuals who give contribution to Autodesk community.
Connect with me on twitter or LinkedIn
Недокументированные сист. переменные
Здраствуйте.
Исследуя дамп, полученный с помощью команды ACADINFO, я натолкнулся на такие системные переменные:
(Добавлено:
Это была предыстория, нижеприведённый список стал больше раз в пять.
Этот список содержит имена системных переменные, которых нет в справке Автокада 2008 рус)
*_AUTHORPALETTEPATH
*_LINFO
*_PKSER
*_SERVER
*_TOOLPALETTEPATH
*_VERNUM
*ACGIDUMPMODE
*ADCSTATE
*ANNOSELECTED
*APSTATE
*AUXSTAT
*AXISUNIT
*BGRDPLOTTIMEOUT
*CLISTATE
*CPUTICKS
*DASHBOARDSTATE
*DBCSTATE
*DEFAULTVIEWCATEGORY
*DRSTATE
*ENTEXTS
*ENTMODS
*ERRNO
*ERSTATE
*FLATLAND
*FORCE_PAGING
*GLOBCHECK
*GRIPLEGACY
*LAZYLOAD
*LIGHTLISTSTATE
*LISPINIT
*LISPRESET
*MACROTRACE
*MATSTATE
*MAXOBJMEM
*MILLISECS
*MSMSTATE
*MULTICOREMODE
*NFWSTATE
*NODENAME
*OPMSTATE
*OSNAPNODELEGACY
*OSNAPOVERRIDE
*PHANDLE
*PRODUCT
*PROGRAM
*QAFLAGS
*QAUCSLOCK
*QCSTATE
*QUEUEDREGENMAX
*R14RASTERPLOT
*RE-INIT
*RENDERPREFSSTATE
*SDI
*SELECTLASTMODE
*SKIP2DREGENS
*SPACESWITCH
*SSMSTATE
*SUNPROPERTIESSTATE
*TBCUSTOMIZE
*TPSTATE
*USEACIS
*USERI1
*USERI2
*USERI3
*USERI4
*USERI5
*USERR1
*USERR2
*USERR3
*USERR4
*USERR5
*USERS1
*USERS2
*USERS3
*USERS4
*USERS5
*VPMAXIMIZEDSTATE
*VSSTATE
*WHIPTHREAD
_AUTHORPALETTEPATH
_LINFO
_PKSER
_SERVER
_TOOLPALETTEPATH
_VERNUM
ACGIDUMPMODE
ANNOALLVISIBLE
ANNOSELECTED
APERTURE
AREA
AUXSTAT
AXISUNIT
BGRDPLOTTIMEOUT
CIPMODE
CPUTICKS
DBLCLKEDIT
DEFAULTVIEWCATEGORY
ENTEXTS
ENTMODS
FLATLAND
FORCE_PAGING
GFANG
GFCLR1
GFCLR2
GFCLRLUM
GFCLRSTATE
GFNAME
GFSHIFT
GLOBCHECK
GRIPLEGACY
LAZYLOAD
LISPINIT
LTSCALE
MACROTRACE
MAXOBJMEM
MILLISECS
MULTICOREMODE
NFWSTATE
NODENAME
OSNAPOVERRIDE
PHANDLE
PSPROLOG
PSQUALITY
QAFLAGS
QAUCSLOCK
QUEUEDREGENMAX
R14RASTERPLOT
SDI
SELECTLASTMODE
SHOWLAYERUSAGE
SKIP2DREGENS
SORTENTS
SPACESWITCH
USEACIS
В хелпе про них ничего не сказано.
Есть ли ещё какая-нибудь информация по этим переменным?
PS У меня Автокад 2008
—————————————
Добавлено:
Вся информация по этим переменным, которую удалось найти, собрана в приложенном файле